The Uniview NSW2020-16T1GT1GC-LPOE-IN is an Ethernet PoE switch with 16 100Mbps PoE ports, one 1000Mbps port and one 1000Mbps combo port, with a 150W PoE budget. It runs from AC mains, so no separate PoE injectors are needed.
The Uniview NSW2020-16T1GT1GC-LPOE-IN (UNV) is an Ethernet PoE switch for powering and connecting PoE IP cameras and other PoE devices over network cable. It offers 16 100Mbps PoE ports, with up to 30W on a single port and 150W across the whole switch.
The NSW2020-16T1GT1GC-LPOE-IN suits a run of PoE IP cameras or other PoE devices that need power and data over one network cable. Its 16 PoE ports are 100Mbps RJ45 ports; the switch also has one 1000Mbps port and one 1000Mbps combo port, which the file does not list as PoE ports.
Power is shared. The switch supplies up to 150W in total and up to 30W to any single port, and the specification lists IEEE 802.3af and 802.3at. If all 16 ports were drawing 30W the total would exceed the budget, so add up the real draw of your devices before you plan the number of cameras.
Uniview lists three working modes. Default mode lets all ports communicate with each other. Extend (surveillance) mode gives transmission distance up to 250 metres, with downlink ports talking only to uplink ports. VLAN (secure) mode also limits downlink ports to uplink ports. A PD keepalive function can restart a camera through PoE power if it stops sending messages.
| Hardware Specification | |
| Ports Type | 16×100Mbps PoE ports (RJ45)+ 1×1000Mbps Gigaethernet ports +1×1000Mbps Combo ports |
| Switching capacity | 7.2 Gbps |
| Power Supply | AC: 100 to 240V, 50/60Hz |
| Forwarding performance | 5.36Mpps |
| MAC | 16K |
| Packet Buffer | 4 M bit |
| PoE Mode | ModeB (4578) |
| Max.PoE Power | Max capacity:150W; Max capacity for single port: 30W |
| Prior Ports | 1 to 8 |
| Standards | IEEE802.3, IEEE802.3u, IEEE802.3z, IEEE802.3ab, IEEE802.3x, IEEE802.3af, IEEE802.3at, IEEE802.3az |
| Cooling Fans | 0 |
| Max.Power | 165W |
| Operating Temperature | 0°C to 45°C |
| Operating Humidity | 10% to 90% (noncondensing) |
| Indicator | POWER:; Steady on: AC input is normal; Off: No AC input; PoE:; Off: No PoE power supply; Steady on: PoE power supply is normal; PoE-MAX:; off :The POE power supply power of the whole machine is less than 80% of the specification; Steady on : The POE power supply power of the whole machine is greater than 85% of the specification; LINK/ACT:; Off: No link; Steady on: Linked; Flashing: Transmitting data |
| Dimensions (W×D×H) | 440*195*44mm |
| Weight | 1.99KG |
| Working Mode | Default (normal) mode: all ports can communicate with each other. Extend (surveillance) mode: transmission distance up to 250 metres; downlink ports can communicate only with uplink ports. VLAN (secure) mode: downlink ports can communicate only with uplink ports. When PD keepalive is enabled, the switch restarts the IP camera via PoE power if it sends no message for a period of time. |
| Compliance | |
| NDAA Compliant | Support |
You need a mains supply (the switch takes AC 100 to 240V, 50/60Hz), network cable to each device, and PoE devices whose combined draw stays within the 150W budget. Match each camera's PoE requirement to the 802.3af or 802.3at ports and to the switch's PoE mode. Tell us your camera models and we will check the total power before you order. See our PoE switches and network cable.
We are a supplier, not an installer. We will go through the NSW2020-16T1GT1GC-LPOE-IN with you before you buy — how many PoE cameras fit the 150W budget, which ports to use, and the cable you need — and depending on your requirements and your area we can recommend a qualified trade installer. We have been operating since 2012 and you can visit our trade counter in Wolverhampton.
It provides up to 150W in total and up to 30W on a single port. Add up the draw of each camera to check that the total stays inside 150W.
The 16 100Mbps RJ45 ports are the PoE ports. The one 1000Mbps port and one 1000Mbps combo port are not listed as PoE ports, so treat them as network connections.
No. Uniview lists cooling fans as 0, so the switch is fanless. Its operating temperature range is 0°C to 45°C.
Extend (surveillance) mode gives a transmission distance of up to 250 metres. In this mode the downlink ports can communicate only with the uplink ports.
Yes. Uniview products are supplied at trade prices to approved trade customers, so the price is shown once you are logged in to a trade account. Call 01902 902251 or see our trade customer page to open an account.
Delivery is within 1–3 working days to England, Scotland and Wales. We do not ship to Northern Ireland.
Yes. Our trade counter is at Unit 3, Park View Centre, 243 Dudley Road, Wolverhampton WV2 3JU. Call first so we can confirm the item is there for you.
Questions on specification or compatibility: call 01902 902251, see our FAQ and support pages, or contact us. Trade accounts are available — see trade customers. Browse the full Uniview range.
| Product Code | NSW2020-16T1GT1GC-LPOE-IN |
|---|---|
| Manufacturer | Uniview |
| Colour | Black |
| Device Port Speed | 10/100 Mbps |
| Device Ports | 16 |
| PoE Ports | 16 |
| Uplink Port Speed | 10/100/1000 Mbps |
| Uplink Ports | 2 |
We provide tailored support for you and your CCTV system.
Many of our Cameras and Recorders come with a comprehensive 3 year warranty.
We've got a fully functioning show room and IP suite to show you exactly how our CCTV equipment works
As cheap as £10, we will deliver your order 3 to 5 working days!
