Pyronix DIGI-4G: Upgrading Alarm Signalling from PSTN and GPRS

If a Pyronix alarm still signals over a phone line (PSTN) or GPRS, it needs a new signalling path before those networks close. Pyronix's answer is the DIGI-4G communicator, which sends alarm signals over 4G, falls back to 2G automatically and works with PyronixCloud. Installers should start these conversations with customers now rather than waiting for the switch-off.

Why signalling needs attention

An alarm that cannot signal is only a local bell. Many older Pyronix systems were fitted with a PSTN dialler such as a DIGI-1200 or voice dialler, or a GPRS module, to send alerts to a phone, an app or a monitoring centre. Pyronix point out that both PSTN and GPRS are being phased out, and systems relying on them risk going offline.

We cover the wider picture, including what the phone line switch-off means for burglar alarms in general, in our guide to the PSTN switch-off and burglar alarms. This article looks only at the Pyronix route.

The Pyronix option: DIGI-4G

DIGI-4G is designed to replace legacy PSTN or GPRS communicators on Pyronix systems.

What it offers

  • 4G signalling for alarm transmission
  • Automatic 2G fallback if the 4G network has a temporary problem, adding a second route for resilience
  • PyronixCloud compatibility, which brings app control, push notifications and remote monitoring
  • Straightforward installation with minimal disruption to the existing system

For many customers the cloud side is the real gain. A system that used to dial a landline can, after the upgrade, be armed and checked from the HomeControl2.0 app.

Planning the upgrade

1. Find the systems at risk

Go through your maintenance records and list every Pyronix system that signals by PSTN or GPRS. Note the panel model, the communicator fitted and whether the customer has an app, a monitoring contract or just a dialler to a phone.

2. Check compatibility

Confirm DIGI-4G is supported on each panel and firmware version using Pyronix's current documentation. Older panels may need a firmware update or may be better replaced.

3. Check signal on site

Mobile coverage inside a building varies. Check the 4G signal at the panel position, particularly in basements, metal-clad units and rural sites, before committing to a date.

4. Talk to the customer early

Pyronix's advice is to contact customers now and be the proactive expert rather than leaving it until legacy networks retire. Booking upgrades on routine service visits spreads the workload and avoids a last-minute rush when everyone needs the same job doing.

5. Update monitoring and app details

If the system reports to an alarm receiving centre, coordinate the change with them and test signals end to end. If the customer is moving to the app, set up PyronixCloud and HomeControl2.0 and show them how it works before you leave.

What end users should know

  • The alarm itself may be fine. Often only the communicator needs replacing.
  • After the upgrade the system can stay connected as networks change.
  • App control and notifications are a useful bonus, not just a like-for-like swap.
  • Ask your installer to check how your alarm signals today if you are not sure.

Buying Pyronix from Zenith

DIGI-4G is not currently listed on our site, so contact us for availability. Our Pyronix brand page lists the panels and modules we stock. Where the panel is too old to upgrade, our Pyronix alarm system builder helps you spec a new Enforcer system. Orders are dispatched within 1–2 working days.

Frequently asked questions

Does my Pyronix alarm stop working when PSTN closes?

The alarm will still sound locally, but a PSTN dialler will no longer be able to send alerts. The signalling needs moving to another path, such as 4G.

What does 2G fallback mean on DIGI-4G?

If the 4G network has a temporary issue, the communicator switches to 2G automatically so the alarm can still signal.

Can I get app control after upgrading?

Yes. DIGI-4G is compatible with PyronixCloud, which provides app control, push notifications and remote monitoring.

Do I need a whole new alarm?

Not always. Pyronix designed DIGI-4G to replace legacy PSTN and GPRS communicators, so a sound system may only need the communicator changing. Check panel compatibility first.

Source: Pyronix, Preparing for the Future: Signalling Upgrades. Product details are correct at the time of writing; always check the latest manufacturer documentation before installation.

Published at: 15-11-2026 / 2 Views
  • Ajax logo
  • AV:Link logo
  • Adastra logo
  • AudioCodes logo
  • Brackenheath logo
  • C.K Tools logo
  • Cisco logo
  • Citronic logo
  • Coast logo
  • Cürv logo
  • Dahua logo
  • EPOS logo
  • Eagle CCTV logo
  • Excel Networking logo
  • Fike logo
  • Gigaset logo
  • Grandstream logo
  • HP Poly logo
  • HiLook by Hikvision logo
  • Hikvision logo
  • Honeywell logo
  • Jabra logo
  • Lexstar logo
  • Mercury logo
  • Mercusys logo
  • Mitel logo
  • Panasonic logo
  • Paxton logo
  • Pyronix logo
  • Ring logo
  • Ruijie Reyee logo
  • SPRO logo
  • Samsung logo
  • Shokz logo
  • TP-Link logo
  • TP-Link Omada logo
  • TP-Link VIGI logo
  • Tenda logo
  • Texecom logo
  • Toshiba logo
  • Ubiquiti logo
  • Unify logo
  • Union logo
  • Uniview logo
  • Valcom logo
  • Visonic logo
  • Western Digital logo
  • Yale logo
  • Yealink logo
  • Yeastar logo
  • Yuasa logo
  • Zenith Security Co. logo
  • Zinc logo