PoE Power Budget Calculator

How much PoE power does your switch need?

Add your cameras, access points and phones. Get the PoE budget, ports and standard, plus a TP-Link, Ruijie, Hikvision or Dahua switch that fits.

Free toolNo sign-upPoE, PoE+ and PoE++In-stock switches

Quick answer: a fixed IP camera uses about 6 watts, so 8 cameras need about 48 watts, or about 58 watts with a 20% margin. An 8-port PoE switch with a budget of 60 watts or more will run them. PTZ cameras and Wi-Fi 6 or 7 access points need much more. See the quick tables below.

Watch: how to use the PoE calculator in one minute.

Work out your PoE budget

1Your devices

How manyDeviceWatts each

2Settings

Room for night-time IR, heaters and future devices.
For adding a camera later.
Non-PoE ports to your recorder or router.

–
Devices draw in total
–
PoE budget to look for (with margin)
–
PoE ports needed

Device figures are typical maximums. Always check the maximum power on your device's datasheet and enter it in the Watts box.

How much PoE power do I need?

Typical maximum power at the switch port, from manufacturers' datasheets:

DeviceTypical powerPoE needed
Fixed IP camera (2MP to 8MP)4 to 7 WPoE (af)
Colour night camera with white light6 to 10 WPoE (af)
Small PTZ camera15 to 25 WPoE+ (at)
Large IR PTZ camera40 to 60 WPoE++ (bt)
Wi-Fi 6 access point12 to 20 WPoE+ (at)
Wi-Fi 7 access point20 to 30 WPoE+ or PoE++
IP desk phone3 to 7 WPoE (af)
Video intercom door station6 to 12 WPoE (af)

PoE standards at a glance

StandardPer port at the switchAt the device
PoE, IEEE 802.3af15.4 W12.95 W
PoE+, IEEE 802.3at30 W25.5 W
PoE++, 802.3bt Type 360 W51 W
PoE++, 802.3bt Type 490 W71.3 W

The difference between the two columns is the power lost in up to 100 metres of cable. Datasheets usually give the device's power at the device, so this calculator checks it against the right-hand column.

How it works

  • Each device's watts are multiplied by how many you have, then added up.
  • The safety margin is added on top. A switch should never run at its full budget: devices draw more at night or in the cold, and you may add more later.
  • The calculator finds your most power-hungry device and tells you which PoE standard its port must support.
  • Ports needed = PoE devices + spare ports. Uplink ports are listed separately, because they do not need PoE.

The formula: PoE budget (W) = sum of (devices × watts each) × (1 + margin). For example, 8 cameras at 6 W with a 20% margin: 8 × 6 × 1.2 = 57.6 W.

Questions

What is a PoE power budget?

It is the total power a PoE switch can send down all its ports at once, shown in watts. Each port also has its own limit set by the PoE standard it supports. Add up what every device draws and choose a switch whose budget is higher than the total, with some room to spare.

How much power does a PoE CCTV camera use?

Most fixed IP cameras use 4 to 7 watts, rising a little at night when the infrared or white light is on. PTZ cameras use much more: small PTZs about 15 to 25 watts and large IR PTZs 40 watts or more. Check the maximum power figure on your camera's datasheet.

What is the difference between PoE, PoE+ and PoE++?

PoE (802.3af) gives up to 15.4 watts per port at the switch, PoE+ (802.3at) up to 30 watts, and PoE++ (802.3bt) up to 60 watts for Type 3 or 90 watts for Type 4. Some power is lost in the cable, so the device receives about 12.95, 25.5, 51 or 71 watts.

How much spare PoE budget should I leave?

Leave at least 20%. Devices draw more when heaters, infrared or white lights come on, and it leaves room to add a camera later. This calculator adds the margin you choose.

How far can PoE run over a cable?

100 metres over Cat5e or Cat6, the same as normal Ethernet. For longer runs use a PoE extender, or a switch with extended range mode, which lowers the speed to reach further.

What happens if I go over the PoE budget?

The switch stops powering some ports, usually the ones with the lowest priority or the highest port numbers. Cameras may reboot at night when their lights come on and the total draw goes up.

Need a hand sizing it? Our Wolverhampton team will check your list and pick the switch.

Call 01902 902251

Planning a whole system? Our CCTV kit builder and network kit builder pick switches that match your devices. Sizing the recorder too? Try the CCTV storage calculator.

We stock PoE switches from TP-Link, Ruijie, Hikvision and Dahua. Browse TP-Link PoE switches, Omada switches and the Ruijie Reyee range, or call our Wolverhampton trade counter on 01902 902251.

  • Ajax logo
  • AV:Link logo
  • Adastra logo
  • AudioCodes logo
  • Brackenheath logo
  • C.K Tools logo
  • Cisco logo
  • Citronic logo
  • Coast logo
  • Cürv logo
  • Dahua logo
  • EPOS logo
  • Eagle CCTV logo
  • Excel Networking logo
  • Fike logo
  • Gigaset logo
  • Grandstream logo
  • HP Poly logo
  • HiLook by Hikvision logo
  • Hikvision logo
  • Honeywell logo
  • Jabra logo
  • Lexstar logo
  • Mercury logo
  • Mercusys logo
  • Mitel logo
  • Panasonic logo
  • Paxton logo
  • Pyronix logo
  • Ring logo
  • Ruijie Reyee logo
  • SPRO logo
  • Samsung logo
  • Shokz logo
  • TP-Link logo
  • TP-Link Omada logo
  • TP-Link VIGI logo
  • Tenda logo
  • Texecom logo
  • Toshiba logo
  • Ubiquiti logo
  • Unify logo
  • Union logo
  • Uniview logo
  • Valcom logo
  • Visonic logo
  • Western Digital logo
  • Yale logo
  • Yealink logo
  • Yeastar logo
  • Yuasa logo
  • Zenith Security Co. logo
  • Zinc logo