Ajax Arming by Device Inactivity: Automatic Backup Arming

Arming by device inactivity is a new Ajax scenario that arms the alarm on its own when the detectors you choose have seen no activity for a set length of time. It is designed as a backup for the most common weakness in any alarm system: someone forgetting to set it. It needs current Ajax apps and firmware, and it does not run on Hub Jeweller or Superior Hub Hybrid.

What problem does it solve?

Most alarm failures are not technical. The panel works, the detectors work, but the last person out did not arm the system, or a key holder left it unset on purpose. Ajax says the feature began as a request from Spain, where empty properties attract squatters and estate agents showing buyers round did not always set the alarm afterwards. The same gap exists in the UK: empty buy-to-let flats between tenants, holiday lets, small offices where staff assume someone else will lock up, and storage units that are visited only now and then.

Rather than relying on people, the hub watches for a period of quiet and then protects the site itself. Users get a notification when the system arms, so nobody is left guessing.

How the scenario works

A resettable timer

You pick which devices the scenario should watch. Every time one of those devices is triggered, the countdown starts again from zero. Only when the full inactivity period passes with no triggers does the hub arm.

What gets armed

The scenario can arm the whole system, arm selected groups only, or switch on Night mode. Group arming is useful for mixed sites, such as a shop with a flat above, where only the commercial area should arm automatically.

Timing and schedule

The inactivity period is set in minutes, hours or both. By default the scenario runs around the clock, but you can restrict it to certain days and times, for example evenings and weekends for an office.

Quick on and off

The scenario can be enabled or disabled with a single tap in the Control tab of the Ajax app, which helps when contractors or cleaners need a site to stay unset for a while.

Practical set-up tips

  • Choose detectors on the main routes. Motion detectors covering hallways and entrances give the clearest picture of whether anyone is still on site.
  • Do not make the period too short. Someone sitting still at a desk or reading in a lounge may not trigger a detector for a while. Start with a generous period and shorten it once you know how the building is used.
  • Use groups for shared buildings. Landlords with several units on one hub can apply the scenario only to vacant units.
  • Combine with schedules. A schedule limits automatic arming to the hours when the site really should be empty.
  • Update first. Ajax states that the latest app versions and device firmware are required, so update the hub and apps before configuring it.

Which hubs support it?

Ajax lists two exceptions: Hub Jeweller and Superior Hub Hybrid do not support the scenario. If you are planning a new system and want this feature, check the hub model before you buy, and if you have an older Hub Jeweller, the feature is a reason to look at a newer panel. Ajax publishes a separate support guide with step-by-step configuration instructions.

Who will benefit most?

  • Landlords and letting agents with empty properties between tenancies or regular viewings.
  • Homeowners who want the alarm to set itself if the family leaves in a hurry.
  • Small businesses that want the office armed after hours without relying on the last person out.
  • Warehouses and workshops that sit idle for long periods.

Ajax also points out that consistent arming can help with insurance conditions. If your policy has an alarm clause, check with your insurer what they expect.

Buying Ajax from Zenith

Zenith Security Co. is an Ajax stockist with a trade counter in Wolverhampton, and orders are dispatched within 1–2 working days. To put together a system that supports this scenario, start with our Ajax alarm kit builder or look at the Ajax Hub 2 (4G) Jeweller panel. You can also compare ready-made intruder alarm kits or browse the full Ajax range.

Frequently asked questions

Will the alarm arm while someone is still inside?

It can if the chosen detectors do not see them for the whole inactivity period, which is why you should pick well-placed detectors and a realistic time.

Can it arm only part of the building?

Yes. The scenario can arm selected groups or activate Night mode instead of arming the whole system.

Does it work on every Ajax hub?

No. Ajax states it is not supported on Hub Jeweller or Superior Hub Hybrid, and the latest apps and firmware are required.

Will I know when it has armed?

Yes. Users receive a notification when the system arms after the inactivity period.

Source: Ajax Systems, Arming by device inactivity: a reliable backup for site security. Product details are correct at the time of writing; always check the latest Ajax documentation before installation.

Published at: 15-11-2026 / 1 Views
  • Ajax logo
  • AV:Link logo
  • Adastra logo
  • AudioCodes logo
  • Brackenheath logo
  • C.K Tools logo
  • Cisco logo
  • Citronic logo
  • Coast logo
  • Cürv logo
  • Dahua logo
  • EPOS logo
  • Eagle CCTV logo
  • Excel Networking logo
  • Fike logo
  • Gigaset logo
  • Grandstream logo
  • HP Poly logo
  • HiLook by Hikvision logo
  • Hikvision logo
  • Honeywell logo
  • Jabra logo
  • Lexstar logo
  • Mercury logo
  • Mercusys logo
  • Mitel logo
  • Panasonic logo
  • Paxton logo
  • Pyronix logo
  • Ring logo
  • Ruijie Reyee logo
  • SPRO logo
  • Samsung logo
  • Shokz logo
  • TP-Link logo
  • TP-Link Omada logo
  • TP-Link VIGI logo
  • Tenda logo
  • Texecom logo
  • Toshiba logo
  • Ubiquiti logo
  • Unify logo
  • Union logo
  • Uniview logo
  • Valcom logo
  • Visonic logo
  • Western Digital logo
  • Yale logo
  • Yealink logo
  • Yeastar logo
  • Yuasa logo
  • Zenith Security Co. logo
  • Zinc logo