Ajax Superior MultiTransmitter (8 Inputs) Fibra Explained

The Ajax Superior MultiTransmitter (8 inputs) Fibra is a Grade 3 board that connects up to eight third-party wired devices to an Ajax Fibra system. It takes its power from the Fibra line, so there is no separate mains feed or backup battery to install, and it fits inside an Ajax casing. It fills the gap between the single-input Transmitter and the 18-input MultiTransmitter Fibra for small and mid-sized retrofits.

Where it fits in the range

We have already covered the general idea of reusing old wiring in our guide to upgrading a wired burglar alarm with an Ajax MultiTransmitter. This post is specifically about the new 8-input Fibra board and why you might pick it over its larger and smaller siblings.

  • Superior Transmitter Fibra – one input, fitted inside a third-party device.
  • Superior MultiTransmitter IO (4x4) Fibra – four inputs plus four relay outputs, as a board for an Ajax case.
  • Superior MultiTransmitter (8 inputs) Fibra – eight inputs, no outputs, powered from the Fibra line.
  • Superior MultiTransmitter Fibra – 18 inputs, mains powered with a 12 V backup battery.

In short, if a site has more wired zones than the IO board can handle but not enough to justify the 18-zone module and its mains supply, the 8-input version is the tidy middle option.

Key specifications

Inputs

Eight inputs that accept NO, NC, EOL, 2EOL and 3EOL wiring, plus KeyArm and roller shutter inputs. That covers most legacy PIRs, door contacts, glass break detectors and key switches you will find on an older panel.

Power

The board runs from the 24 V Fibra line and provides a 12 V output, up to 0.5 A, to power connected detectors. Because the hub's line supplies it, there is no extra power supply unit or standby battery at the module, which means less to wire, test and maintain.

Grading

Ajax states that it fully complies with EN 50131 at Grade 3. In the UK, EN 50131 is applied through PD 6662, so the module can form part of a Grade 3 design for higher-risk commercial premises, provided the rest of the system is specified to match.

Mounting

It is supplied as a board rather than a boxed device. Fit it in a compatible Ajax casing: Case A (106), Case B (175), Case E (395) or Case D (430). Ajax has a case configurator to check what will fit together.

Practical uses

Retrofitting a small commercial site

A shop or office with a working wired alarm can keep its motion detectors, door contacts and glass break sensors and move them onto an Ajax hub. The cable runs stay where they are; the old panel is replaced.

Adding specialist detectors

Seismic detectors, hold-up buttons and roller shutter contacts are not all in the Ajax catalogue. The 8-input board lets you bring them in as zones.

Remote management

Once connected, each wired device shows its state in the Ajax apps, can be configured remotely and can trigger automation scenarios, just like a native Ajax detector.

Planning tips for installers

  • Fibra modules need a hub with Fibra lines, such as the Superior Hub Hybrid. Ajax's announcement does not list hub compatibility, so check the current compatibility table.
  • Add up the current draw of the detectors you will power from the 12 V output and stay within 0.5 A; use a separate supply if you need more.
  • If you need relay outputs, for example to trigger a strobe or a gate, the IO (4x4) board is the better choice.
  • Survey existing cabling and resistor values before quoting.

Buying Ajax from Zenith

Our Wolverhampton trade counter stocks Ajax Fibra equipment, with orders dispatched within 1–2 working days.

Frequently asked questions

Does the 8-input MultiTransmitter need its own power supply?

No. It is powered from the Fibra line and has no backup battery of its own.

What grade is it?

Ajax says it complies with EN 50131 Grade 3, the grading used under PD 6662 in the UK.

Does it have relay outputs?

No. It has eight inputs and a 12 V supply output only. For relays, look at the IO (4x4) Fibra board.

Can it be fitted without an Ajax case?

It is designed as a board for a compatible Ajax casing, such as Case A, B, D or E.

Source: Ajax Systems, The right capacity for wired integrations: meet Ajax Superior MultiTransmitter (8 inputs) Fibra. Product details are correct at the time of writing; always check the latest Ajax documentation before installation.

Published at: 15-11-2026 / 1 Views
  • Ajax logo
  • AV:Link logo
  • Adastra logo
  • AudioCodes logo
  • Brackenheath logo
  • C.K Tools logo
  • Cisco logo
  • Citronic logo
  • Coast logo
  • Cürv logo
  • Dahua logo
  • EPOS logo
  • Eagle CCTV logo
  • Excel Networking logo
  • Fike logo
  • Gigaset logo
  • Grandstream logo
  • HP Poly logo
  • HiLook by Hikvision logo
  • Hikvision logo
  • Honeywell logo
  • Jabra logo
  • Lexstar logo
  • Mercury logo
  • Mercusys logo
  • Mitel logo
  • Panasonic logo
  • Paxton logo
  • Pyronix logo
  • Ring logo
  • Ruijie Reyee logo
  • SPRO logo
  • Samsung logo
  • Shokz logo
  • TP-Link logo
  • TP-Link Omada logo
  • TP-Link VIGI logo
  • Tenda logo
  • Texecom logo
  • Toshiba logo
  • Ubiquiti logo
  • Unify logo
  • Union logo
  • Uniview logo
  • Valcom logo
  • Visonic logo
  • Western Digital logo
  • Yale logo
  • Yealink logo
  • Yeastar logo
  • Yuasa logo
  • Zenith Security Co. logo
  • Zinc logo